New Two Zone System - I'm out of my League


Hello,

I've read a ton of the Home Theater posts and everyone is super knowledgeable and helpful.  I'm kindly asking for everyone's advice.

I have always been a two-channel (amp, pre-amp, tower speakers) person.  My wife and I are remodeling our main floor and now the two towers have to go - I'm sure you can guess why!


Zone 1:  In the living room I will have two in-wall speakers - left/right speakers on the sides of the TV and a powered subwoofer.  Unless you suggest otherwise, I'd like to use my existing Parasound amp and pre-amp separates to power the two in-walls and send an audio signal to the powered subwoofer (using "loop output" on the amp).  These speakers will mainly be used for TV watching, and occasional music playing.  I have no interest in anything more than this 2.1 set-up.


Zone 2:  In the kitchen on the same floor as the living room I will have two in-ceiling speakers.  These speakers will play music.  I was thinking I would power these speakers with an integrated amp.


Most times - it will be the TV audio playing through the in walls in Zone 1 and music playing through the in-ceilings in Zone 2 (simultaneously).  This is easily accomplished with the set-up I described above (I believe).  My question / confusion is this - I'd ideally like the option to play music from the same source in the two zones at the same time (same music playing through all four speakers in the two rooms).  Can you please tell me the easiest / best way to accomplish this flexibility?


Thanks in advance for any help you can provide.

Matt

mminor

Unfortunately, the only way to get where you want to go is either a full blown Home Theater Processor or a AV Receiver. I don’t know of any 2-channel preamps that will do a "zone 2". The HT Processor or AV Receiver will replace your existing 2-channel preamp and will act as a source selector and volume control for both Zone 1 and Zone 2 speakers. You will need to supply an amplifier for Zone 2 if you choose an HT Processor (an integrated is not needed). Some AV Receivers can use other speaker outputs for Zone 2 (such as the "height speakers"). If you are still interested in this path, give us the following details and we can help guide towards a solution:

- What is your current model preamp/amplifier?

- What is your budget for this HT Processor / AV Receiver?  This also decides the audio quality you will get out of this device.

- Do you have any specific video source requirements such as HDMI, 3D or 4K? Tidal, Netflix, streaming, DLNA?

You’ll have to replace your current preamp. The HT Processor route is the better way to go for sound quality and to keep your current amplifier. However, your budget may force you to do an AV Receiver if you want all the bells and whistles (4K, Netflix, tidal, streaming, etc.).

Hi AuxInput.  Thanks so much for your detailed and quick response - I really appreciate it.  My more in-depth details are below.


Amp = Parasound HCA-1500A (200 watts per channel, 2 channels)

Pre-Amp = Parasound PLD-2000

$1,000 = Budget for HT Processor / AV Receiver (I'm still not clear on the difference between the HT Processor and AV Reciever)

Video = HDMI 4k / 18GB, Netflix, streaming - I originally was going to run the HDMI directly from the cable TV box to the TV and then run Audio left/right from the TV to the preamp.  I will also have a cat5 cable going to the TV (for streaming).  But I understand the HDMI can carry the audio signal as well, I'm def open to / looking for suggestions here.


I'm fine not using / replacing my current Parasound preamp.  If I use the HT processor or AV Receiver - will I be able to choose which zone I use my current Parasound two-channel amp with (Living Room, in-walls)?


Please let me know if any further info would be useful.  Thanks again for all your help!

Matt



Perhaps a Bluesound Node for each room, if you get the integrated for the kitchen, connected wirelessly, would allow you to stream music to both rooms.
I use it for my office (2nd floor) and living room (1st floor). It works perfectly. And, it doesn't cost an arm and a leg. 
I am using the Node 1, which I bought on Ebay for around $200 each. 
The Node 2 has a better DAC, so it might be better if you are not planning on using a separate DAC like I do.
B

An AV Receiver has several types of inputs for audio and video, including several HDMI inputs, digital coaxial and toslink digital inputs, along with many 2-channel RCA audio inputs. This can include old style composite and component video inputs. An AV Receiver has multi-channel amplifiers for anywhere from 7 to 13 channels (you can hook up speakers directly to the receiver. The AV Receiver will also have RCA preamp outputs so you can hook it to any amplifier as well.

An HT Processor is pretty much the same thing, except it does not have internal amplifiers. It is a preamp/processor only and requires an external amplifier for all speakers. This allows the company to use more of the space inside for better power supply and analog circuits. Many HT Processors also have XLR balanced outputs.

For the best sound quality situation in your budget, I would recommend getting a used Marantz AV7702 processor. The 7702 is just recently been discontinued by Marantz and they can be found on ebay for anywhere between $800-1200 (or more if new-in-box).

If you don’t like getting used stuff, you can look for a new Marantz SR5011 or SR6011 AV Receiver. They will not have as good sound quality as the AV7702 processor. On the receivers, I generally recommend buying the highest one you can afford. The Marantz receiver models are pretty much functionally all the same. The difference is that the higher models have a better/larger power supply which translates into better sound quality. SR5011 is typically $799. SR6011 can be gotten from BH Photo & Video for $1149.

You can still use your Parasound amplifier with the receiver for main movie speakers. You can use a couple of the speaker connections on the receiver for the Zone 2 kitchen speakers (so you wouldn’t have to buy an additional amp).

I recommend connecting all audio/video sources (bluray, satellite, cd, etc.) to the processor/receiver and letting the processor/receiver decode and manage the audio/video. It will also have the benefit of doing bass management for your powered subwoofer.  The Marantz devices also have Ethernet input so you can stream from DLNA or internet.  If you want Netflix, you can hook up a Roku or use a Sony Bluray player to stream from Netflix