Received The MC2000 Back From Expert Stylus Today


So I got the Ortofon MC2000 back from Expert today, and Mr. Hodgson did a beautiful job on this service. He fitted a new Paratrace stylus and made a minor repair to the end of the OEM cantilever. Looks as new, and there are no oddities to the stylus assembly. The Paratrace diamond is quite diminutive, barely able to be seen with my aging eyes. 

This afternoon I installed it on a very light Fidelity Research headshell, looks kind of like one of the Swiss cheese SME ones. Wired it to a T2000 transformer and then to a Graham Slee Accession. 

This is a remarkably detailed and neutral sounding cartridge. I have a few decent cartridges here and this is as good as any I have experienced. My system uses a pair of JBL 4365 speakers and a Halcro DM8 pre amp, so I have to be careful with system synergy as a too clinical component can push it over the edge. The MC2000 comes very close to doing this. I am considering a wood headshell like the Yamamoto boxwood, due to its low mass and its ability to add a touch of warmth/body to the overall sound. 

But even as it sits the transparency, the fine detail, the dynamic contrasts are all outstanding. I can tell after an evening of listening this is a keeper for me, and while its been a bit of a drawn out journey to accumulate the bits and pieces and get the cartridge serviced...well...it was worth every bit of effort. 

Yes I enjoy my Transfiguration, ZYX, and Ikeda, that is true. But I like the MC2000 every bit as much and I would get rid of a whole bunch of stuff before I ever parted with this cartridge. 

neonknight

Nikola, If I ever see one for sale (T2000), I will let you know.  In the interim there are a few sources for custom made SUTs; you can have one made with a turns ratio to suit the MC2000.  (I would favor Intact Audio, but I am biased.) But for me the way to go would be to use a current-driven phono.  The MC2000 actually makes a lot of current compared to other LOMCs, because of its very low internal resistance.  The nominal current output is .05mV/2 ohms = 25 micro-amps.  If you do that calculation for other LOMCs, the MC2000 comes out quite well up there for current output.

neonknight, I am not sure if we refer to the same box. My is

luxury wooden box ( 30x15x6 cm) with two ''levels'' . On the

level ''above'' is the cart + headshell. The lover ''level''contains

other parts . 

Dear Lew, My MC 2000 is the only MC cart with such low output.

All other I can drive with my Klyne and Basis Exlusive. So the

question is if the cost ''equal'' spending? 

True.  Which is why I haven't bought a current-drive phono stage for the MC2000; it's the only LOMC I own that would need it.  The box built for me by Dave Slagle actually is nominally current driven, but its input impedance is higher than the output impedance (2 ohms) of the MC2000, so actually it operates in voltage drive mode.  The way I think of it, the cartridge drives the phono stage, not vice-versa.

@nandric 

Yes that is the box I am referring to. I don't think I can be any clearer, its ALL the OEM packaging that was provided when you bought it new. I even have the lapel pin. The only item I do not have is the Ortofon RCA cables that were provided with the T2000. I have a cardboard box that held the cables, but not the cables themselves. Otherwise I have everything else that comes with the MC2000 and T2000. 

I know a retired dealer who used a MC2000 in a top end LP12. I heard it and it sounded very good. Detailed but a little thin and bright in the upper mids for my taste. He has since changed to Garrard 401 and Decca cartridges with claimed musically superior results. Coincidentally, that's what I run too.