Pass labs xa25 amp and BW 804 d3?


Can the Pass labs xa25 drive BW 804 d3's?
128x128gweedoargus
B&W says 50 wpc minimum, the amp is 25 wpc. So, I rather doubt it will play anything but softly before clipping.
Though I know Pass has a rugged build, why push it?
B
I figured as much. Think I'm going to go with the new parasound A21+. Any thoughts?
While the XA25 is rated at 25 watts into 8 ohms and 50 watts into 4 ohms, John Atkinson's measurements that were reported in Stereophile indicated that it is capable of providing 80 and 130 watts into those impedances, respectively.  A lot of that disparity is apparently due to the Pass specs being based on distortion percentages that are extremely tight and are much lower than the ones JA bases his results on, and presumably some of that difference reflects the amp's capability after entering class AB mode rather than class A.

The speakers are rated at 89 db/2.83 volts/1 meter, with impedances of 8 ohms nominal and 3 ohms minimum.

FWIW, my XA25 has no trouble cleanly generating 105 db peaks at my 12 foot listening distance, with 6 ohm speakers rated at 97.5 db/1 watt/1 meter.  However 89 db speakers will require approximately seven times as much power as 97.5 db speakers to generate a given volume.

My guess as to the bottom line is that the answer will depend on the dynamic range of the recordings you listen to, with classical symphonic recordings that have been engineered with minimal or no dynamic compression being among the most challenging kinds of recordings in that respect, as well as your preferred listening volume, room size, and listening distance.

Regards,
-- Al 
The Parasound Halo A21 is a good amp especially for the money. Highly recommended! 
Post removed 
Kosst said it perfectly. The pass is much better and more like 100wpc in A/B operation. 
I'm about 8 ft. from the speakers. Probably about 15 ft wide for the listening area. Although, the room is completely open behind my listening position. Approximately, 32 ft total in length from behind the speakers to the end of my kitchen, a total open floor plan.. I know pass is a better amp, that's why I am hoping for it to work. I don't listen to any classical, but I listen to everything else. I want to listen to classical though because I love music. I am CD only using a roksan k3, emotiva xsp 1 gen 2 pre and an emotiva xpa 2 gen 1 amp.  Emotiva is leftover from my more entry level system. It sufficed before getting 804s, except for the xsp 1 gen2 which replaced an emotiva USP 1. The xsp 1 is nice for $1200.it can replaced later. I need a solid amp. I am strictly 2 channel. $5000 is my absolute limit. I appreciate all the advice I can get. Still on the fence. Maybe the pass labs will work? Any other recommendations?
Thanks again
Post removed 
I know pass equipment and their Class A amps are quite powerful.
It should drive the B and Ws easily and sound very smooth and detailed.
If your room is really large and you need additional volume go to one of their Class A/B amps to get the extra power.  
As I said, I know Pass overbuilds his amps, and you might not have any issues, but once again, why tempt fate?
If it were me, I'd take the safe route and get a higher powered amp. I believe in having lots of headroom when it comes to power.
 Then if you decide to change speakers,you'll have a wider range to choose from.
I see some XA-30's for sale that are under $5K, still low, but closer to recommended specs. There are a pair of XA-100's, asking $6.5K though, but would be a real killer.
There are other manufacturers, but I don't know if Pass is the only one you'll consider.
Bob
Gweedoargus,
You have gotten some good responses and comments. I’m inclined to agree with those who have raised the very important consideration of ’sound quality ’ as compared to increased quantity (higher oower/more watts). The Pass Labs XA 25 is capable of 50 watts of pure class A into a 4 ohm load (this isn’t an insignificant amount). It can provide class AB 200 watts maximum into a 2 ohm load (This is impressive).

The John Curl designed Parasound A21 offers class AB 250 watts into 8 ohms and 400 watts into 4 ohms. So clearly higher power. I suspect it has pretty decent sound quality. Keep in my its DF (Damping factor) is >1100!! This suggests very heavy use of NFB. Some very respected amplifier builders such as Atmaspere and Roger Modjeski consider this amount of DF gratuitous and without meaningful benefit. On the other hand some builders (John Curl I’m sure) would beg to differ. My gut feeling is that the Pass XA 25 could very well be the superior sounding amplifier.

Is there the interest/desire to home audition these amplifiers and actually hear them driving your B&W speakers? I would bet that the vast majority of your listening the XAX25 would remain in class A operation. This is a good thing IMHO. I'm expressing my own biases. I don't believe in the cliche of "the more power the better" once you have sufficient power the objective should be placed on quality. 
Good luck,
Charles
Post removed 
Kosst_amojan,
I agree with your calculations and reasoning. This is the point I was attempting to illustrate in my prior post. You can’t look at the XA 25 and conclude, "oh, it’s just a 25 watt amplifier " . There’s considerably more going on here if one can appreciate the design/circuit and implementation. As you calculated, at very reasonable (even generous) volume levels these speakers aren’t demanding much power/ watts at all. And as a reminder, 200 watts/10 amps  (current max) into a 2 ohm load.

DF of 500 is still pretty high relatively speaking in regard to the XA 25. I agree the XA 25 and XA 30.8 are notably different circuit designs. I’ll empathize again, Parasound A 21 or one of the Pass Labs amplifiers, you have to hear them with the specific speaker of interest. Each amplifier will have its own sonic signature with a given speaker.
One point to consider regarding DF is it is inversely proportional to the output impedance (isn’t necessarily a bad thing) and the higher the DF the more NFB utilized (Which ’could’’ introduce some undesired sonic consequences of its own). Another point,  speaker sensitivity measurements are of a single speaker.  Generally 3 db is added when discussing a "pair" of speakers. 
Charles

Seems like Pass has some very knowledgeable owners. 
If they say it can work, who am I to disagree?
Hi B,
If I  am among those you're referring to, I do not own  a Pass Labs amplifier. I'm  just  aware of their design objectives and the very conservative power rating method they employ. 
Charles 
Post removed 
Thanks for your very informative posts, Kosst. I’ve learned some things from them about my own XA25 that I didn’t know previously.

Regarding the references in one of your posts to "average volume," others should keep in mind that what matters with respect to an amp’s maximum power capability is of course the maximum volume levels that are reached on the recordings that are listened to, not the average level. And the relation between the maximum and average volume levels will vary dramatically among different recordings, depending on both the music and on how much dynamic compression has been applied in their engineering.

For example, some classical orchestral recordings that have been engineered with minimal or no dynamic compression may reach brief dynamic peaks that are 30 db or more greater than the average level of the recording. Which in turn means that around 1,000 times as much power will be required to reproduce those brief peaks compared with the amount of power required to reproduce the average level of the recording. While many and perhaps the majority of pop and rock recordings are compressed to a dynamic range of less than 10 db, which will require less than 10 times as much power for peaks than for the average level.

Thanks again. Best regards,
-- Al
Post removed 
Thanks so much everyone.The core values of these forums are to help, instruct, inform and intrigue. The amount of knowledge and experience that has been directed my way makes decisions a little less stressful. My gut says pass xa25. Thanks again.
@almarg Didn't know you'd switched to this amplifier. Are you subbing out with the VAC, or have you switched completely to the XA-25?
@Cal3713, I’ve sold the VAC Renaissance 70/70 MkIII amplifier and I’m using the XA25 exclusively. I decided to purchase the XA25 a few months ago while the VAC was back at the factory for a minor repair, motivated mainly by all of the glowing reviews I’ve seen of the XA25. While also taking into account the sterling reputations of Pass Labs and the dealer from whom I purchased the amp (Reno HiFi) for customer service and support, as well as Pass Labs’ reputation for building products that tend to be reliable and trouble-free over the long-term. Regarding the reviews, I found Teajay’s (Terry London’s) review to be especially accurate in its characterization of the amp’s sonics, at least with my easy to drive Daedalus Ulysses speakers.

Following are some comments about the XA25 that I had occasion to post a few months ago in a thread that was mainly on a different subject:

It comes amazingly close to the VAC with respect to dimensionality, imaging, liquidity, and other traditional fortes of high quality tube amps. It’s a bit less rich sounding than the VAC, but I interpret that as an increase in accuracy, which is fine as far as I am concerned.

There are also some non-sonic factors favoring the XA25, including the likelihood of greater reliability in the years ahead considering the age of the VAC; the fact that even though both amps operate in class A the XA25 puts only 240 watts of heat into the room compared to what I believe is upwards of 700 watts for the VAC; and the cost that would be involved in re-tubing eight 300Bs if and when that were to become necessary.

This is the first time I’ve had a high quality solid state amp in my system in about 25 years, and I believe I’ve picked the right time and the right model with which to do so again.

On another note, happy holidays to you and yours, and all best wishes for 2019!

-- Al
@almarg Thanks al. Always happy to see one of your posts in a thread, and glad you're enjoying the pass.

5 years ago I had an xa30.5 that I loved and have considered using the new model on my coincident PREs (in liu of the 300b Frankenstein's).  I'll have to keep eye out for a used one to try. It's been tough to beat those amps (so far I've tried lyngdorf and atma-sphere) Dealing with pass is also leagues better than my coincident experiences.  

Happy holidays to you too.

- Chris
@cal3713 I also own a Pass Labs XA25 amp, which I received a few weeks ago, and like you, I also own a pair of the wonderful Coincident Frank mkIIs, which I've had for while now.  Being a tube guy, especially SET, I have not been able to live with any SS amps I've heard in the last few years, that is, until I got the XA25. Teajay did nail it with his review of the XA25, and so did the other reviewers.  This is an amp that is voiced with the midrange first, which is also my preference, but nothing is missing from either extremes.  If you can't get the midrange right, forget everything else.  Both amps have a wonderfully holographic soundstage (the Franks may have a slightly deeper soundstage), natural sounding midrange (voices are intoxicating with either), good instrument tonality and timbre.  The XA25 has, as it should, better slam / impact with a deeper, more controlled bass.

Anyways, my personal assessment of the XA25 is that it is the equal of the Franks, though it doesn't sound like SET, it's neither better nor worse, just a bit of a different flavor, very easy to live with, and IMO, certainly a "keeper". I get the emotional connection to my music with either amp, so bottom line, I love them both!
Jeepers, you Pass owners are really PASSionate about your amps.
I have learned a lot from your posts. I did not realize the XA-30 implemented an entirely different topography. But, then I just an Ayre guy...
B
Post removed 
Dear Readers;
I run my Vandersteen Model 5s with a Pass Labs X250.  The x250 has never left class A operation as indicated by the front panel meter.  The sound level if desired, can be quite high.  Maybe not rock concert level, but very adequate for home use.  Hope this helps.
Post removed 
Macguy said his meter indicates the amplifier remains in "class A operation". So the first 20 watts of the x250 is bias in class A (bias set  at 0.8 for this model per the Nelson Pass article). At his listening levels the Vandersteen speakers aren’t demanding of more than these first 20 watts. I suspect that very often not more than a few watts are utilized at easonable listening levels.
Charles
Post removed 
I do understand the desire/concern of many listeners in regard to "headroom" availability for demanding musical peaks and the fear of having insufficient ’juice ’ on hand. This is a common topic in audio forums. I do think that to some extend it gets blown out of proportion. I do not agree with the popular audiophile axioms, "the more power the better" or "enough power is never enough".

I’ve read (more than a few) testimonials on various forums from those who drive their 100 db> horn speakers with 200- 300 watt amplifiers so that they "never run out of headroom" regardless of volume or music genre demands. So without any doubt there are those who have different perspectives and experiences. Speakers of this type can provide reasonable SPLs (65- 75 db C weighted) with only 1/20- 1/100 (0.05 to 0.01) of 1 watt
Charles
A minor point but one that should probably be mentioned is that the Vandersteen 5 has a built-in amplifier handling the deep bass. And it is designed to be used with a passive high pass filter inserted between the preamp and the power amp, which rolls off low frequencies by 3 db at 100 Hz and at 6 db/octave below that frequency. (The built-in sub amp provides a complementary frequency response which restores overall flatness). So the power that is demanded of Macguy’s X250 is significantly reduced relative to what be required if it were driving a comparably efficient speaker full range.

In any event, it appears that the Vandersteen 5, like the currently produced 5a Carbon, is rated at 87 db/2.83 volts/1 meter, but apparently has an 8 ohm nominal impedance rather than the 5a Carbon’s 6 ohms. Assuming those specs are accurate it can be calculated that at a typical listening distance of say 10 feet, and in a medium sized room, two such speakers will produce an SPL for a centered listener that is in the vicinity of 95 db when both are driven with 20 watts. Enough for many listeners on most or all of their recordings, but certainly not enough for some listeners, especially on recordings having wide dynamic range.

I do not agree with the popular audiophile axioms, "the more power the better" or "enough power is never enough".
I disagree with those axioms as well, Charles. A point that seems to often be overlooked by proponents of those axioms is that for a given level of amplifier quality more watts usually = more $, at least within a given amplifier topology and a given class of operation (A, AB, D, etc.). So if a given amount of money is to be invested in an amplifier of a given topology and class of operation, choosing an amp that has more power capability than necessary may very well mean that more of those dollars than necessary will be directed toward watts rather than toward quality. At least that’s how I see it.

Best regards,
-- Al
Well this explains Macguy's observation of his Pass Labs X250 not leaving class A operation while driving the Vandersteens, 95 db SPL is plenty loud for many listeners. Al thanks for the additional information and the always keen commentary. 
Charles 
I own a Pass XA-25. When I bought it I owned a new CJ ART150 stereo tube amp and a CJ Premiere 12 monoblock set up. I’ve had the legendary CJ Premier 350 solid state amp. I drive Wilson Audio SOPHIA II’s. I got here with an XA25 after exchanging email with Nelson Pass when I was thinking of a First Watt to try out. He re-directed me to take a look at the XA25. That was in November 2018. I have sold the ART 150 and other amps. Compact and commanding. I read the STEREOPHILE review and the technical assessment. All I can tell you is the little amp commands the Wilsons with authority. My sound has never been better. It paired extremely well with CJ single ended pre amps such as the ET-5 and Premier 16LS2. I tried a Pass Labs XP-10 which was a very good pre, but traded it for the XP-20. This little amp can and does command with authority. The reviews of the sound are dead on. I also use a ELAN Z cooling fan as well; it of course runs hot so the fan helps.
I received my Pass Labs XA25 today. It easily drives my 804s and it is actually runs just as cool if not cooler than my emotiva xpa 2 at high volume. It barely gets warm to my amazement. Sound quality is spectacular even though it is yet to be broken in. I think I will invest in the Pass Labs Hpa 1 headphone/preamp combo as a preamp. I like to keep things simple. I don't need any bells or whistles for my 2 channel listening. Thanks again for the advice.
Post removed 
Although I suspect that you would have been very likely satisfied with the Parasound A21 amplifier I believe you selected the better sounding amplifier. I’m glad you weren’t swayed by those suggesting the Pass XA25 would be under powdered for your speakers. Congratulations and I’m happy for your very successful outcome. You describe the sound quality as "spectacular" that pretty much says it all. Just think about this, sound quality will improve as hours of use accumulate. 
Charles
Completed my demo of the xa-25 a week ago. It was a great amp. Smooth and warm (warmer than my Coincident Franks) and really nice bass performance. In the end I did decide to stick with the 300bs however. They were a bit more "real" and holographic. I think maybe a bit more accurate too as far as imaging goes. Close call though, the pass was really a great amp.
I had B&W Nautilus 804s for years, and have heard most of the B&W lineup over time. I can tell you, without reservation, that B&Ws are power hungry and, IMHO, need at least 150 wpc to even begin showing what they can do. Personally, I paired them with a 225 wpc power amp and they sounded good. 
I'd be wary of taking too much stock on the built in meters on amps. It seems to me that most are at best a rough guide and not to be confused with calibrated laboratory test equipment.
From all the commercial and user reviews it would appear to me that the XA25 is the best sounding SS amplifier for all except the most inefficient speakers.  Is this how most others see this.
@jetter, like many of us I wouldn’t consider my range of experiences to be extensive enough to put it quite as broadly as you did in your question. But I would certainly consider the XA25 to be a very strong candidate that should be considered by anyone looking to purchase a solid state amp in its price range or higher, for use with speakers having medium to high sensitivities.

Also, thanks to the others who have recounted their experiences and provided additional perspectives on this very special amp in recent posts. Enjoy!

Best regards
-- Al
Thanks Al, I am kind of conflicted for the first time in a while. I always wanted a high powered amp and am on the fence between the Parasound A21+ power and the Pass XA25 sound quality. I can score a fairly good deal on both, and now am fairly tempted to buy both and sell whichever after using them in my system.  
@jetter Perhaps it's not quite as good of a deal, but for shipping only RenoHIFI will let you demo the XA25 for 10 days. A nice risk free way to hear the amp.  That's what I did.
Thanks cal, thinking about calling Reno.

gweedoargus, now that you have had your XA25 for a couple of weeks and you are a little more familiar with it could you provide a little more in depth review of how you are liking it?  Its tonality, soundstage and is it powering your speakers as you hoped? Plusses and any minuses.  I am considering this amp myself.
A bit late here, but...

I’m running Wilson Sophia 3s with the Pass XA25. The Sophia’s are ~87db/1W efficiency. They are made easy to drive (nominal 4Ohm impedance), but not all that efficient. I’ve had the XA25 since last Summer.

90 - 100 db is about the loudest I’d listen to, so the Pass is barely loafing most of the time at 1 - 3 watts or so. (I thought I needed high-power too until I actually tried the XA25, thanks to Reno Hi-Fi’s trial period.)

I can turn it up louder than I want to listen to it without any noticeable compression, soundstage collapse, or clipped transients or dynamic swings.

I posted some comments on my experience with the XA25 on other threads (you can search my threads or for XA25). It’s keeper for me.


Why don't you call Pass (talk to Kevin) and ask him whether its enough power?  That's what I did when getting a recommendation of an amp for my Thiel 2.4's.  I was all prepared to spend a fortune on the XA series monoblocks and they actually talked me out of it, advising that for my speakers the X series was a better match, and that the X150.8 would be more than enough power.  They were right.  I've never heard a greater change for the better just by changing out a power amp.  Its astonishing.  Far more detail, quiet, and a little midrange warmth characterize the Pass products.
Post removed