I am running a pair of Martin Logan ESL 13A speakers (24-23,000 Hz). I would have thought with two 10" woofers there would be more bas (the base level dial on the rear of the speakers doesn’t seem to cut it either).
In the past I had a pair of ML Spires (29-23,000 Hz) with only one 10" woofer that had so much base, I sold my pair of ForceField 30s. Not the case with the 13A’s.
I don’t have a lot of room, maybe 16" or so square and I was wondering about a pair of SVS Micros. Do you think they would complement the 13As or do I need something bigger?
Martin Logan has come out with a few new subs lately; do you think I should keep in the ML family?
Hoping to come in under $2K, so used is fine. Thanks all!
I should also mention I’m limited on space so placement would likely have to be on the inside or the outside of the main speakers (same back wall).
I was wondering about a pair of SVS Micros. Do you think they would complement the 13As or do I need something bigger?
IMO the SB1000 Pro is a much better sub than the Micro and not all that much bigger, and on top of that they’re significantly cheaper and you can get two for under $1200. No brainer in my book if you can fit them. Hope this helps.
I ran Infinity RS1B towers with my stuff. Nothing worked better. You will see most big loudspeaker systems run towers. I see Tekton sells a few different kinds, I'd be tempted..
Martin Logan Abyss10 that they just came out with.
Also if you can find a force cancelation sub that might work also. The ML balnceforce 10 is just a hair too big. As is the Rythmik G22. I own a power sound audio dual 12 that they don't make anymore.
I run 4 SB-1000's (no Bluetooth). Small, tight, sealed box, and they were cheap ! The front one's in are in phase. The rears are 180° out of phase, Tunes the room's Bass nodes perfectly. I still have a 50Hz - 60 Hz hump in the room. But I like it. I don't use any DSP and chose to tune the room instead.
I listen to A LOT of SACD's/DSD files and refuse to convert the DSD to a PCM stream (been there, done it, got the T-Shirt).
What is the size of the room the MLs are in? Did you get the Anthem room correction for it? Does it have a bass EQ function? I can help you figure this out, but I need this info first. It is possible you may not need a subwoofer at all.
I have 2 x SVS 3000 micro's used with Trinnov correction alongside my Wilson Benesch front speakers in my Lounge. The micro's were chosen over the SB1000's only because I could not get a position (as I do in my other room where I have SVS 16's to get front firing alignment (partly done with Sneakers Track 4, partly with Trinnov). I would agree with @soix and @rajugswthat the 1000 / 1000 pro would be better for that use and would have gone that way if space allowed (micro's are behind slightly outboard). But they do (with the correction applied) do a very good job. But, I haven't tried to time align them through position without the correction and I suspect, having tried that once before with a Kef dual firing unit that it would be more difficult to get a satisfactory result and both this and discussions with Trinnov on emerging technologies such as their wave forming would, wherever possible lead me towards a front firing sealed box wherever possible.
I use dual Rythmick F12. I offer no recommendations as to your specific subs questions, but I will offer one about placement. Placing both subs either right inside or outside of the speakers is far from ideal. In my house of stereo it resulted in very overly bloated bass along the back wall of the room. I then took the advice of one of the members here who said subs need to be on different walls and at different locations. After experimenting, one ended up on the right side of the front wall, the other a third down along the left sidewall. The result was astounding, it solved all my bloated bass issues.
I don't think I would go any smaller than 12" drivers for subs, but I have heard REL and KEF subs with smaller drivers that were surprisingly good for their size, but expensive.
I would look at the SVS SB-1000 or get a pair of Rythmik sealed subs for the best sound. The Rythmiks would be a little over budget, but a worthwhile investment. If you can find a different place to hide a small sub and get it somewhere else in the room, the SVS subs might be better. There are wireless options and they come with an app that lets you adjust the sound remotely.
@soixThanks for the suggestion, you have always been an advocate for the SB1000s. They seem to be a great deal.
@russ69 are you saying move on from the MLs and hook up with some Infinity RS1B towers or Tektons?
@dmaddox77Yes, I heard something about ML’s new subwoofer line, but I don’t see them for sale on their website yet, but I will check it out.
@mijostyn My room is 15’ wide x 22’ long with the kitchen off to the right of the right speaker, you can see pictures in my virtual system. Yes, I have the ARC kit. I tried this when I first got the speakers and wasn’t all that impressed with the results. I will definitely give it a shot again. Thank you for reminding me about this Mike, any help would GREATLY be appreciated!
@audio_rd_ukand others who have chimed in, thank you!
@big_greg the wireless option sounds great, do you think is a good way to go, is wireless going to be accurate match with the rest of the system? Hardwired, at least for most audio products, seem to be the preferred set-up.
My room is 15' wide x 22' long with the kitchen off to the right of the right speaker
That's actually a pretty big space when you include the Kitchen and vaulted ceiling which you have to account for. You will have to think about pressurizing the entire space to get satisfying bass and I think that's why you feel the mains aren't doing the job. You will probably be happiest with a pair of traditional subs 12" or bigger.
You are welcome, the room I have the micro's in is 27 x 15, but no 'space off' and notwithstanding my and others on the SB1000's, etc., They manage, with two other 10" subs in the rear corners to pressurise. I am not disagreeing with @rick_nthat if you can fully pressurise with some larger say 12's (precisely why I have 2x16 1x12 and 2x10 (soon to be 2x13.8) in the main room that you won't appreciate it. But when I have my audio set using the SVS 16's in the main room it is timed impact and timed midrange reinforcement, rather than out and out pressurisation that makes it sound "musical". The arc should align 2.2 which ever sub you chose well because Trinnov manages to great effect in mine even with not ideal sub-placement. If arc for some reason doesn't then perhaps see if somebody can give you a home demo on either something with dirac, or a trinnov (amethyst or st2-hifi, latter would be ;old stock') just to see what can be achieved in the room. Correction ARC or other could give you more flexibility with placement on subs. But the (see REL video you tube) placing using track 4 from sneakers should give a good start if you can place them alongside the speakers. As Rick_n notes 2x12" so SB1000 pros (with the 5% off for "godual").
Just another quick couple of things. I have had the speakers in lots of different positions with little effect on the sound, so I have them in ML’s recommended position with the backs 10" from the wall and 24" off the one of the side walls, the other side is wide open to the kitchen.
I’ve also found treating the room with dipole speakers doesn’t have a large effect on the sound quality. I have tried acoustic panels behind the speakers, and it didn’t sound good at all. I have no side wall to the left and on the right side, I can pull the curtains closed.
ML say ceiling treatment aren’t needed but do recommend treating the back wall (behind the listening position) which I have done.
ML also says there is no set measurement for the space between the speakers. I have mine 6’ apart and my listening position is approximately 11’ back from them. Toed in via ML's flashlight recommendation.
I think REL overstates what is truly needed in their room guide. I have a HT room that is similar in size to your room. I'm running a pair of SB4000s and it's all the bass I need. The sound is smooth and the room is fully pressurized. If you want to go the REL direction I think that the SB2000 or SB3000 will get the job done. The SVS subs are very popular and can usually be found on the second hand market. Good luck and cheers.
."@russ69 are you saying move on from the MLs and hook up with some Infinity RS1B towers or Tektons?"
No, the ML13A are fine speakers. My brother ran ML Requests for a long time. A stereo pair of towers does amazing things. You will get entirely new and deeper sound stage.
EDIT: I prefer stereo subs on the inside of your main loudspeakers.
@navyachtsOK, I reviewed your pictures. Does the Anthem program have EQ capability? Can you increase certain frequencies manually? I assume you measure the speakers with a microphone? You should put sound absorption directly behind the speakers. It will improve your imaging and dampen sibilance.
I also use ESLs and have been since 1978 along with subwoofers. If we can advance the low end 10 dB at 20 Hz keep it flat to 60 Hz then curve it down to zero dB at 100 Hz you should be fine without added subwoofers as long as the drivers and amps can handle the volumes you like to listen at. If not then we have to fill in with subwoofers from 80 Hz down. There are not many commercial subwoofers that are clean enough for your system. Martin logan has its balanced force subs, but you will need two subs. Do not even think about one. In your situation I think the best subs would be the KEF KC 92. They are also balanced force and you can get them in white which would fit your decor. They are quite small. I would put one right next to each ML, either side will do. I am hoping you will not need them.
Bricasti Design just loaned me an M1 DAC to play with. Nice unit! I live about 30 minutes from the factory in Shirley, Mass.
I am a happy Rythmic 15 in sealed sub user. Contact them and they will give you guidance on the best sub(s) for your application. They are very reasonably priced given their performance and flexibility.
I am not sure if I can increase certain frequencies manually, nor am I sure about the program having EQ capabilities. Even if these features were available to me, I’m not sure if I could figure out how to do it. This kinda sounds a little to techie for me.
If we can advance the low end 10 dB at 20 Hz keep it flat to 60 Hz then curve it down to zero dB at 100 Hz you should be fine without added subwoofers as long as the drivers and amps can handle the volumes you like to listen at.
I have 11As and use 2 REL S/812s more to improve the soundstage than for deeper bass. Sounds great. Also I have gotten better sound by moving them 30" from the wall behind them. Room treatment has helped enormously, especially the Stillpoints Aperture 2 panels. Hope you get there. Joe
@navyachtsI do not know that program. You have to jump in and read the manual. If you give me the exact product name I might be able to download the manual and give you a hand. You might want to look into those KEF subwoofers in the meanwhile.
HI I have two SVS SB 1000 pros supporting my Canton 9k stand mounted and they were a piece of cake to set up,sound good and fill in seamlessly,and they are well within your budget,and have a good reputation. Having said that I have no experience with other subs so there is that.
@navyachts"you have 5 subs in your room, with another two on their way?"
I have 5 in the room but the two rears were down firing ported studio because I could not at the time get a front firing that would fit and was balanced. But recently I have been discussing development of wave forming with Trinnov and front firing would be much better for this so the rear down firing will be replaced by the Norwegian Arendal 1723 subwoofers that are strictly speaking 'side firing' or double side firing. Are 18.9" H x 13.2" D x 17.7" W. With a 13.8" driver in a sealed enclosure. Not as good 'value' as the SVS on $/watt / inch. But I cannot find a better alternative as I have a 15" depth restriction. And my son gets two subs for his AV room.
I have a single ML BalenceForce 210 in a substantially bigger room (20x24) than you do and it does the job with my ML CLXs. It might be nice to have a pair for stereo bass, like I had with my Entecs, but it eats up floor space I need.
The Ml BF subs have the advantage of being able to use a ML supplied crossover for your 13As. There are two, one if you want to run the 13As full range, and another if you want to roll them off in the bass. I run my CLXs full range. Then, with the PBK kit and Anthem software, you can create a custom BF output profile that can give you a much flatter in-room bass response. I can’t imagine using a sub that can’t do this. The before and after is night and day.
I don’t know much about their new subs, maybe they do all this for less money. I would call them and also look on the ML forum.
@navyachtsThe ML Balanced Force speakers are great, but they are even larger and more expensive. I think the KEFs will do the job, fit in better and cost about 1/2 as much. Warning, one sub is never a good solution. You are better off without any.
If you do a lot of listening from one listening position just keep the microphone at the listening position for all measurements. If you tend to listen more as background music then use the 5 locations as per instructions. Now, you have level controls for bass and midbass. Run the program then turn the midbass down just a little and the bass up as far as it will go. Then start decreasing the bass a little at a time until things sound right to you. I am not sure if this will work, but give it a try. It costs you nothing. A thing to remember is a balanced sound at lower levels with have too much bass and treble when you turn it up. I recommend balancing the system at the loudest levels you listen. When you turn it down the bass and treble will seem a little low unless you have a loudness control.
the wireless option sounds great, do you think is a good way to go, is wireless going to be accurate match with the rest of the system? Hardwired, at least for most audio products, seem to be the preferred set-up.
In the past I had 2 or 3 of my subs connected by wireless. Ichandelier to hard wired, mostly because the transmitters I had at the time were a little fussy. I didn't notice any difference in sound quality. You don't have to connect them wireless, my thought was that might give you more placement options.
The SVS subs I own don't have the app control feature, but I think it would be really helpful for set up.
Another potential for your consideration.
Just seen a review by Nemo Propaganda on youtube of the Buchardt Sub10 where it was compared to both the Kef and the SVS 3000 Micro. Different form factor to the KEF but has a good app and a level of built in correction for less than the Kef 62. Might be worth a look. I confirm @big_greg's, expectation that the SVS Apps are very good. If anything the Buchardt looks more sophisticated, are very usefully the microphone set up for the room correction is done by linking it to an iphone which it uses as a mic. The results of this are noted to be as good as connecting it to a dedicated room correction mic. Seems to be $1400 each. Less than the Kef, about $500 more than the SVS, but suggested to be better than the SVS and slightly better than the more expensive Kef.
@navyachtsI will have a look at Steve Huff’s, I just knew the other guy had reviewed the Kefs and SVS Micro’s. If Buchardt did something a little bigger, say a 12 or 13 size wise they would be great for my rear set up.
But if those 10’s are big enough for your room, placement seems to be very flexible
Not that I want to turn you away from a UK manufacturer like Kef - UK HiFi Development is part of my ’income’, though not on any product I’ve ever commented on here.
@navyachtsThere is not a single driver subwoofer that can match a balanced force subwoofer for accuracy. That leaves only KEF, Magico, Martin Logan and myself as options and I am not building any more. See building resonance free subwoofer thread below.
Just my 2 cents, but placing the subs next to the Martin Logan mains may not solve your bass issues. If the lack of bass is caused by where the mains are positioned within the room, then adding subs may do little or nothing to help.
You must have a verified phone number and physical address in order to post in the Audiogon Forums. Please return to Audiogon.com and complete this step. If you have any questions please contact Support.